Fabrication

SLAC National Accelerator Laboratory is operated by Stanford University for the Department of Energy. As a management and operating contractor, subcontracts awarded by the Laboratory are not Federal procurements, and are not directly subject to the Federal Acquisition Regulations in 48 CFR. Nonetheless, certain Federal laws, Executive Orders, and regulations may affect our DOE approved purchasing system, as required by statute, regulation, or contract terms and conditions.

Please review the listed requirements and provide your best and final offer for both price and lead-time.

The follow has been attached for you to complete and review:

1. Representations & Certifications Rider
2. Confirm Attached SLAC terms are accepted: FP Commercial Supplies-Services T&Cs (August 2023)
3. Confirm Attached SLAC terms are accepted: SLAC General Terms and Conditions Supplemental Rider (Rev. August 2026)

1. Quote#7775

Required item(s) listed below:

1. DSG-000110672                                                            QTY: 1

1. DSG-000102297 Clamp Diamond Ring               QTY: 8
2. DSG-000102297 Clamp Diamond Ring               QTY: 10

Total - DSG-000102297 (18)

1. DSG-000103435 Tube, Collim Lid                          QTY: 20
2. DSG-000103435 Tube, Collim Lid                          QTY: 16
3. DSG-000103435 Tube, Collim Lid                          QTY: 2

Total - DSG-000103435 (38)

1. DSG-000103585 Plate, Identifying Collim          QTY: 10
2. DSG-000103585 Plate, Identifying Collim          QTY: 6
3. DSG-000103585 Plate, Identifying Collim          QTY: 1

Total - DSG-000103585 (17)

1. DSG-000103609 Mt, Collimator                             QTY: 10
2. DSG-000103609 Mt, Collimator                             QTY: 8
3. DSG-000103609 Mt, Collimator                             QTY: 1

Total - DSG-000103609 (19)

1. DSG-000105043 Base, HE Light Tight 5mm       QTY: 6
2. DSG-000105043 Base, HE Light Tight 5mm       QTY: 4

Total - DSG-000105043 (10)

1. DSG-000106241 Base, HE Light Tight 10mm    QTY: 4
2. DSG-000106241 Base, HE Light Tight 10mm    QTY: 1
3. DSG-000106241 Base, HE Light Tight 10mm    QTY: 1

Total - DSG-000106241 (6)

1. DSG-000106252 Base, HE Light Tight 15mm    QTY: 1
2. DSG-000106252 Base, HE Light Tight 15mm    QTY: 1

Total - DSG-000106252 (2)

1. DSG-000106275 Base, HE Light Tight 20mm    QTY: 2
2. DSG-000106275 Base, HE light Tight 20mm     QTY: 2

Total - DSG-000106275 (4)

1. DSG-000055232 HE YAG Retainer                         QTY: 40
2. DSG-000055232 HE YAG Retainer                         QTY: 32
3. DSG-000055232 HE YAG Retainer                         QTY: 4

Total – DSG-000055232 (76)

1. DSG-000098971 Base, HE Light Tight 3mm       QTY: 1
2. DSG-000098971 Base, HE Light Tight 3mm       QTY: 1

Total - DSG-000098971 (2)

1. PF-375-108-45 Diode Block                                      QTY: 20
2. PF-375-108-45 Diode Block                                      QTY: 16
3. PF-375-108-45 Diode Block                                      QTY: 2

Total - PF-375-108-45 (38)

Quote is for product only; no on-site services permitted.

Source selection will be based on Lowest Price and Technically Acceptable Method (LPTA).

Technical evaluation criteria are as follows:

• 1. 1. 1. This is a UHV (Ultra-High Vacuum) component. As such, the following restrictions apply:
• EDM machining is NOT allowed without prior approval by SLAC
• The use of sanding discs, grinding wheels or abrasives is prohibited
• The use of sulfur-containing cutting fluids and silicone lubricants is prohibited
• All parts must be cleaned before welding

1. 1. 1. 1. Provide dimensional inspection reports.
         2. UHV machining: No EDM without prior SLAC approval. No sanding discs, grinding wheels or abrasives. No sulfur-containing cutting fluids or silicone lubricants.
         3. DSG-000055232 - Disregard note 2, part will be cleaned at SLAC.
         4. Requires electropolish: DSG-000098971, DSG-000106241, DSG-000106252, DSG-000106275
         5. PF-375-108-45 - Disregard note 3, part will be cleaned at SLAC.
         6. REF-000376156 (DSG-000102297) Do not install helicoils.

Please provide a price and lead time quotation by COB 10/20/2026.

Please be advised that the requirement was also posted on SAM.gov.

Send quote to marissat@SLAC.stanford.edu.

Is there any room for additional discount such as for Academic, ICPT, GSA, or Government Institutions?

If possible, please provide a link to your webpage for published price list to substantiate for the prices quoted.

• Buy American Act Certification (BAA) applies to items that have a unit price that is over $15,000.
• Representations & Certifications Rider is required. Once completed the Reps and Certs is valid for one year until renewal. If you have already completed one within the year please disregard. Otherwise, please complete and return.
• Please include in your proposals the Harmonized Tariff Schedule (HTS Code) & ECCN if applicable.
• All subcontractors are required to register in the System for Award Management (www.sam.gov).
• The resulting purchase order will be issued on a fixed price basis. SLAC National Accelerator Laboratory Terms and Conditions for Fixed Price Commercial Supplies and Services (Rev. August 2023) and SLAC General Terms and Conditions Supplemental Rider (Rev. August 2026) will be made a part of the resulting order.
• Payment Terms will be NET-30 (SLAC is unable to do advance payments and or Prepayments).
• Freight terms will be FOB Destination Prepaid and Add
• Foreign Vendors Shipments will be made CIP SLAC, Menlo Park, and Duty Unpaid. 

You are requested to mark and identify proprietary/confidential information provided in response to the solicitation.

Contact me directly with any questions.

Kind regards,

Marissa Tanomrat

Procurement Commodities Team

SLAC National Accelerator Laboratory

2575 Sand Hill Road

Menlo Park, CA 94025

Email: marissat@slac.stanford.edu