Turbine and Generator Hydroelectric IDIQ

Turbine and Generator Hydroelectric Component Manufacturing and Rehabilitation IDIQ THIS IS A SOURCES SOUGHT ONLY. This Sources Sought notice is being issued solely for information and planning purposes - it does not constitute a Request for Quote (RFQ)/Invitation for Bid (IFB)/Request for Proposal (RFP) or a promise to issue an RFQ, IFB or RFP in the future. No formal solicitation for this work exists at this time. All qualified concerns may submit capability statements for consideration. Capability statements received will be reviewed to determine the technical, administrative, and management capability of such offerors to perform this type of work. The capability statements will be used to determine appropriate procurement strategy, in particular, whether a set-aside or an alternate procurement strategy is warranted. The Government does not intend to award a contract and will not pay for any information or administrative costs incurred in response to this notice. The Bureau of Reclamation, Lower Colorado Region, Lower Colorado Dams Office (LCDO), at Hoover Dam, Davis Dam, and Parker Dam power plants has a requirement for the repair, remanufacture, machining, and rehabilitation of existing hydro power plant related components. These hydro power plant components may vary from items such as the generator, turbine, elevators, cranes, water passage valves and gates, barricades, and any component found in a fully functioning hydroelectric powerhouse and dam facility. This IDIQ includes the following types of work: Manufacture of new components Re-design and reverse engineer replacement components to include: -3-dimensional digitizing and computer-aided drawings of existing Lower Colorado Dam hardware -Repair or replacement manufacture of existing Lower Colorado Dam hardware Furnish new hydroelectric turbine and generator components to replace existing worn components including: -Large valves -Valve actuators -Bearing components -Water passage gates -Any component that wears or needs upgrading Provide onsite repair and/or machining Weld and repair fatigued, worn, or water-damaged hydro turbine-generator parts to precision dimensions and tolerances of Lower Colorado Dam design. Provide precision fabrication of new replacement parts per Lower Colorado Dam design. Provide industry standard inspection and testing. Assembly of turbine-generator parts from newly purchased components or components previously purchased and stocked at Hoover Dam. Types of components include, but may not be limited to: -Wicket gates -Stator/pole wedge bars -Wicket gate bushings -Wear plates -Engineered fasteners -Retaining bolts -Break-off screws -Large diameter valves, valve bodies, and leaves -Large diameter coupling studs and nuts -Thrust bearing components -Bearing brackets -Shift rings -Laminations -Insulation -Other generator & turbine components In addition, for components too large to transport for repair, the contractor shall also provide onsite repair/machining. Repair/machining work performed onsite shall be subject to Construction Wage Rate Requirements statute prevailing wage rates. For any on-site work, the task orders will identify the need for a site specific safety plan, job hazard analysis, hazmat and special work permit, and security clearances. Each year, Hoover Dam performs a major maintenance overhaul teardown on one of its 17 hydro turbine-generator units. There are nominal dimensional and configuration variations among the turbine-generators, but the basic design layout, assortment of parts and teardown procedures are consistent throughout. The anticipated North American Industry Classification System code is 333611, Turbine and Turbine Generator Set Units Manufacturing, with a small business size standard of 1,500 in number of employees. Product Service Code J028 Maintenance, Repair, and Rebuilding of Equipment- Engines, Turbines, and Components. The basic contract is anticipated as an Indefinite-delivery/Indefinite-quantity (IDIQ) contracts. The ordering period is anticipated at 5 years. In accordance with FAR 36.204, disclosure of magnitude of construction projects, the estimated prices are Between $25,000 and $100,000; Between $100,000 and $250,000; Between $250,000 and $500,000; Between $500,000 and $1,000,000; Between $1,000,000 and $5,000,000; and Between $5,000,000 and $10,000,000. The IDIQ maximum is more than $10,000,000. The capabilities package should include the following information: 1. Provide business name, DUNS number, address, point of contact to include e-mail address, telephone number and website if applicable; 2. Business size and type (Small business, Women Owned Small Business, HUBZone, Service-Disabled Veteran Owned Small Business, Indian Small Business Economic Enterprise, other); 3. Demonstrate the firm's capability and experience by providing a list of projects completed where the work involved similar contracts in the past five years, and in which your firm performed the work. Additionally, for each project listed, provide the following: a brief description of the work performed, project title, dollar value of the job, prime/subcontractor, location, and the customer's contact name and phone number for the work completed. (not to exceed 5 pages) 4. Bonding capacity per contract/action; All responses must be submitted via email no later than 5:00 pm Eastern Time February 28, 2025. Email address: mwatanga@usbr.gov. Include the reference number (DOIRFBO250010) in the subject line. When it is determined that a formal solicitation will be issued, the pre-solicitation notice will be posted on Contract Opportunities at sam.gov web site at http://sam.gov/.